How To: Convert Your Truck Bed Into An Actual Bed

How To: Make a Sketchy Bed in the Back of Your Truck

What’s viewed by some as a habit of vagrants and degenerates is not only practical but en vogue.
This article originally appeared in the November 2016 issue of TransWorld SNOWboarding. Check out more from the magazine here. Subscribe here!

PHOTO: Taylor Boyd

Sleeping in vehicles has been a thing since the automobile was invented. Prohibition-era folk passed out in their Model Ts after too much moonshine, and VW vans have seen more than shuteye since the sixties. These days, having a rig you can snooze in is all the rage. And it’s practical. As soon as the cost of hotels or burden of crashing on someone’s couch is eliminated, a world of options opens. You can get away with sleeping almost anywhere, often positioning yourself closer to the chairlift or trailhead than friends indoors. Once your rig is dialed, more trips are in the scope of possibility.

Check out more adventurmobiles here!

The method that follows is rudimentary. Are there more elaborate ways to build a setup in the back of your pickup? Absolutely. Something more structurally sound or better engineered? Undoubtedly. But if you want to elevate your mobile slumber scenario beyond a sleeping pad on your damp truck bed and add some welcome storage below—cheap and on the fly—this should do the trick. I’ve woken up in numerous driveways, forests, and parking lots thus far, and it hasn’t collapsed on me yet. In fact, it feels quite sturdy. Not bad, considering I went to the lumberyard one afternoon, bought some wood, and hoped things would work out. $80 poorer, and lo and behold, they did.

PHOTO: Taylor Boyd

— Truck

— Topper

— Cold tolerance

Approximate build time:
One hour

This is based off the bed dimensions of a 2002 Tundra. Take some measurements of your own truck and adjust accordingly.
— One 12-foot long 2×8 board. For more storage below, use 2x10s or 2x12s.

— One 8-foot long 2×8 board.

— Two sturdy sheets of plywood.

— 2 ½ inch wood screws.

— One twin or full mattress. I found mine for free on the side of the road. No bed bugs yet.

— Drill with bit to match screw head

— Circular saw

— Clamps

— Measuring tape

— Pencil

1. Cut 2x8s to a couple inches shy of your truck’s bed length. Let’s say 6 feet. As long as the tailgate will close, you’re good.
2. Cut plywood to the same length. Using this 6-foot example, you would be taking two feet off the end of each 8-foot sheet.
3. Measure distance between sides of your truck’s bed, where the tailgate sits. Let’s say it’s 5 feet wide.
4. Cut each sheet of plywood lengthwise. Their combined width once cut should equal the measurement in step 3. Using the 5-foot example, they could be 2 feet and 3 feet, or 2 ½ feet and 2 ½ feet, respectively. This determines how much storage each side has.
5. Measure the distance between the inside of your wheel well in the truck bed and the edge of the bed, where the tailgate meets the sides. Let’s say it’s 7 inches.
6. Screw one sheet of plywood to the “two-inch” side of one 2×8, running parallel. In this example, the outside edge of the 2×8 should be 7 inches from the edge of the plywood.
7. Add center support.
8. Screw one portion of the plywood into the center-supporting 2×8, halfway across its “two-inch” width, leaving the other half to support the other sheet.
9. Screw the other sheet of plywood into the remaining half of the “two-inch” side of center-supporting 2×8.
10. Position the remaining 2×8 against the other wheel well and screw the plywood to it.
11. Throw your mattress on top.
12. Stash your snowboard below.
13. Drive to the mountains.

Things you may want to get your rig fully dialed:

— Lantern

— Curtains

— Storage bins

— Warm sleeping bag + additional bedding

— Trekking pole for fishing items out of the abyss

— Large water bottle with generous opening. Ladies, you’re on your own here.

More from TransWorld SNOWboarding here!

Source: TransWorld SNOWBoarding

No Comments Yet

Leave a Reply

Your email address will not be published.